- 您现在的位置：买卖IC网 > Sheet目录1210 > DK-SI-4S100G2N (Altera)KIT DEV STRATIX IV TRANSCEIVER
6–2
1
Chapter 6: Stratix IV GT Transceiver Signal Integrity Demonstration
LCD Information
To configure the Stratix IV GT FPGA, perform the following steps:
1. Start the Quartus II Programmer.
2. Click Add File and select the path to the desired .sof .
3. Turn on the Program/Configure option for the added file.
4. Click Start to download the selected file to the FPGA. The FPGA is configured
when the progress bar reaches 100%.
To determine if the appropriate test design .sof is programmed, check the LCD for the
test design number. Refer to “LCD Information” for more information.
LCD Information
The LCD shows the following information:
■
■
■
The Stratix IV GT device junction temperature in Celsius.
The power in watts for the different transceivers (VCCA_L/R, VCCT, VCCR,
VCCH_GXB, VCCL_GXB) and core (VCC) voltage supply rails. Turn the rotary
switch SW16 to observe the different voltage supply values. To learn more about
the switch position for displaying the various supply rail values on the LCD, click
the Help button in the demonstration application.
The sof/pof number that is programmed is indicated by ‘pof ’ followed by the
number.
The power values shown for the VCCA_L/R and the VCCH_GXB assume that the
jumper settings are set to 3.0 V and 2.5 V, respectively. Click the Help button to see the
required jumper settings.
Running the Demonstration Application and Test Designs
The demonstration application communicates with the set of test designs provided
with the kit. You can change the various transceiver parameters that are described in
this section.
To run the application, make sure that the board is powered up properly and there is a
USB cable attached, then go to the
< install dir > \kits\stratixIVGT_4s100g2_si\demos directory and double-click on
stratixIVGT_si_demo.exe file. Ensure that the Stratix IV FPGA is programmed with
1
Certain DLLs are required for the demonstration application
(stratixIVGT_si_demo.exe ) to function properly that are not included with the kit
installation software. These needed DLLs are installed with the Quartus II
Subscription Edition software, version 9.1. Once installed, you can immediately
uninstall the Quartus II software afterwards if you don’t want to purchase a license.
To enable the application to communicate with the board, click the Connect button. To
close the application, click the Disconnect button ( Figure 6–1 ).
Transceiver Signal Integrity Development Kit,
Stratix IV GT Edition User Guide
January 2012 Altera Corporation
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DLP-2232H
MODULE USB ADAPTER FOR FT2232H
DLP-2232ML-G
MODULE USB ADAPTR FOR FT2232D LP
DLP-2232MSPF
MODULE USB ADAPTER WITH MCU
DLP-CB-DLPC200-10R
BOARD CONTROLLER FOR DLP
DLP-D-G
MODULE USB SECURITY DONGLE
DLP-HS-FPGA2
MODULE USB ADAPTER FOR FT2232H
DLP-IOR4
MODULE LATCHING-RELAY 4-CH
DLP-TEMP-G
MODULE DATA-ACQUISITION 3-CH
相关代理商/技术参数
DK-SI-4SGX230N
功能描述:可编程逻辑 IC 开发工具 FPGA Development Kit For EP4SGX230
RoHS:否 制造商:Altera Corporation 产品:Development Kits 类型:FPGA 工具用于评估:5CEFA7F3 接口类型: 工作电源电压:
DK-SI-5SGTMC7/ES
功能描述:可编程逻辑 IC 开发工具 FPGA Starter Kit For Stratix V 5SGTMC7 ES
RoHS:否 制造商:Altera Corporation 产品:Development Kits 类型:FPGA 工具用于评估:5CEFA7F3 接口类型: 工作电源电压:
DK-SI-5SGTMC7N
功能描述:可编程逻辑 IC 开发工具 FPGA Starter Kit For Stratix V 5SGTMC7
RoHS:否 制造商:Altera Corporation 产品:Development Kits 类型:FPGA 工具用于评估:5CEFA7F3 接口类型: 工作电源电压:
DK-SI-5SGXEA7/ES
功能描述:可编程逻辑 IC 开发工具 FPGA Starter Kit For Stratix V 5SGXEA7 ES
RoHS:否 制造商:Altera Corporation 产品:Development Kits 类型:FPGA 工具用于评估:5CEFA7F3 接口类型: 工作电源电压:
DK-SI-5SGXEA7N
功能描述:可编程逻辑 IC 开发工具 FPGA Starter Kit For Stratix V 5SGXEA7
RoHS:否 制造商:Altera Corporation 产品:Development Kits 类型:FPGA 工具用于评估:5CEFA7F3 接口类型: 工作电源电压:
DK-SL900A
制造商:ams 功能描述:Development kit for SL900A EPC Gen2 Sensory Tag IC
DK-SOC-10AS066S-A
功能描述:Arria 10 GX FPGA Evaluation Board 制造商:altera 系列:Arria 10 GX 零件状态:有效 类型:FPGA 配套使用产品/相关产品:Arria? 10 GX 内容:板 标准包装:1
DKSPS-001
制造商:Cooper Bussmann 功能描述:SMALL PARTITION PLATE DP25, DP35, DP45 A - Bulk 制造商:COOPER BUSSMANN 功能描述:SMALL PARTITION PLATE DP25, DP35, DP45 A